1, The device dedicated to the exchange of LED ball bulbs, 220V, 110V LED energy-saving lamps finished detection aging voltage of 220V LED energy-saving lamps, high-voltage, medium-voltage, atmospheric pressure and low-pressure, high-temperature, roaming, shock zone observe the LED energy-saving lamps can be passed above voltage segment aging test.
2,tooling plate bulb lights and 1.2 m lamp aging;
3, to achieve product aging time-four hours;
4,across the board for a total of 133 chain plate, each chain plate mounted the E27 five cartridges lampholder 16, T8 Fluorescent Lamp Holder 4 pairs of aging Bulb 2128 or 532 fluorescent tubes (across the board to send full).
1, temperature zone: thermostat system using electric heating complete the set lower 9 m heated section, the second meter installed two the 1KW ceramic heating tube, three temperature collection point, automatic temperature control: room temperature +80 ° C.
2, detect impact beats circuit: Tianzheng regulator 10KW regulator 1 units,0-250V adjustable set up across the board six districts, each district, the impact of time can be set on a touch screen interface.
3 the detecting of normal circuit: 0-250V adjustable Tianzheng regulator the 10KW regulator 1 units, set to normal pressure test. (Regional range of about 7 meters).
4, the detection of low-voltage circuits: 0-250V adjustable Tianzheng regulator the 10KW regulator 1 units, set to low pressure test. (Regional range of about 7 meters).
5, the detection of high-voltage circuit: Tin genuine regulator 10KW regulator 1 0-300V adjustable, set to a high-pressure test. (Regional range of about 7 meters).
6 ,Bulb chain plate E27 screw lampholders;
7, lamp aging using fast T8 tube seat fixture installed. (Lamp Tower fixture can mobilize the sub 300mm,600mm,900mm,1200 mm);
Appearance and protection requirements:
1, fuselage, rack 40 * 40 * 1.5 (MM) steel pipe welding is made of 130 * 23 (MM) aging line of special aluminum alloy, shield 1.2MM cold plate by bending up and down the fuselage ;
2 inch Double pitch single inclined two holes chain transmission chain;
3, online on the set light barrier passport, using a combination of plexiglass and aluminum plate profiles effectively reduce the energy-saving lamps glare, and better protect the eyes.
4 across the board total with two electric groove track, using insulating epoxy board. Assembly 3MM thick copper conductive strips. Assembling a line body the protective drop resistance network to prevent the product from falling broke, the use of high-quality stainless steel on both sides of the pore network universal angle iron fixed.
5, device not rust, dust is generated.
6, device noise: 65dB.
7 feet with galvanized adjustable level adjustable height cup feet.
Line body shape
1 line body total length: 12 meters, the face and the ground height 750 ± 20mm adjustable.
2 Dimensions: L12000mm * W1620mm * 1270mm (see the LED aging line outline drawing in Annex)
Power and transmission:
1 The motor three-phase motor with Taiwan Yongkun 1.5KW 1:200 reducer, 2HP inverter frequency stepless speed, line speed 0-2M/min adjustable 0-4 hours of aging time is adjustable.
2, 1 inch T17 tooth double pitch sprocket with of φ50 spindle and a tensioning mechanism for transmission.
1, fuselage, rack: rack with 40 × 40 × 1.5mm square steel tube welding made into; fuselage using a special aluminum alloy 130 × 23 × 2mm aging line.
2, nose, tail guard is made of 1.2mm cold plate bending. The lower shielding plate with 1.2mm cold plate bending system, equipped with a 3mm thick brown plexiglass observation window, one meter section, each equipped with two clasping.
3, conveyor chain: Hangzhou Chain Factory produced C212A double pitch the single ear high strength with two holes chain. 30 * 30 GB angle steel support rails, down a total of two-story
4, chain plate: 2.0mm cold plate bending rolled into 148 × 1390 × 57mm each chain board installed a unipolar empty
Open 16 E27 five cartridges lampholder, 4 groups of adjustable bit T8 Fluorescent Lamp Holder. The bottom mounting Er conductive brush (bronze).
6,conductor rail: across the board above with three conductor rail, using the 5mm epoxy boards and rack insulation. Assembly 3mm × 30 stainless steel aging special conductive tracks.
7.The safety net: online body assembly a protective drop resistance network, smash off the lights to prevent production of high quality stainless steel pore network, specification 12000 × 1400mm on both sides with universal Jiaotie fixed.
Electronic control system:
1, the cabinet: 1.2 mm cold plate bending rolling into 730 × 1250 × 1800mm ,40 × 40 × 1.5mm iron square tube support, two storeys arranged. Upper instruments, small conventional control element, the lower is the regulator.
2, control elements: with ammeter, digital voltmeter and lights to display the input voltage and three-phase current. The system adopts Mitsubishi PLC and 7-inch touch screen control Nobukatsu touch screen interface to adjustable shocks aging time and start-stop transportation;
3, the electrical box and line body of the tube with an emergency stop switch for emergency shutdown. With three-color warning lights to display the equipment operating conditions.